BECOME A CORE MEMBER HERE

Author Topic: CMM jk billet front grab handles  (Read 1819 times)

Offline kent10sne1

  • Visitor
  • Posts: 4791
  • KARMA : +37/-128
CMM jk billet front grab handles
« on: April 22, 2016, 10:44:32 AM »
http://www.carolinametalmasters.com/products/cmm-jk-billet-front-grab-handles

My new cage has grab handles built in and these had to come off for it to fit.   Retail 160.  no scratches, all hardware to install driver/pass.

club price = $80  will wait a week and then post on other forms.

Jeep Wrangler Sport JK 2012. //SKULL//
Kent Casey
37 PitBull Rocker's on ATX AX756 beadlock wheels
3.5FOX RESERVOIR COIL-OVER CONVERSION,5.13 Gears/Eaton Rear Locker
AtlasII 4.3.1 Dynatrac ProRock 44 Front Axle
MC Fenders & Sliders upgraded skids
http://www.gatrailriders.com/GTRForums/index.php/topic,15401.372.html

Offline Jeepster1407

  • C.O.R.E MEMBER
  • *
  • Posts: 3763
  • KARMA : +18/-35
Re: CMM jk billet front grab handles
« Reply #1 on: April 22, 2016, 11:52:10 AM »
Good deal! What cage did you go with ?
Most LCOG Builds are like a fat girl in Yoga Pants, just cause it fits doesn't mean it works...

Offline kent10sne1

  • Visitor
  • Posts: 4791
  • KARMA : +37/-128
Re: CMM jk billet front grab handles
« Reply #2 on: April 22, 2016, 12:02:18 PM »
PS seemed the more sturdy route. 
Jeep Wrangler Sport JK 2012. //SKULL//
Kent Casey
37 PitBull Rocker's on ATX AX756 beadlock wheels
3.5FOX RESERVOIR COIL-OVER CONVERSION,5.13 Gears/Eaton Rear Locker
AtlasII 4.3.1 Dynatrac ProRock 44 Front Axle
MC Fenders & Sliders upgraded skids
http://www.gatrailriders.com/GTRForums/index.php/topic,15401.372.html

Offline Blue J

  • Visitor
  • Posts: 2758
  • KARMA : +19/-191
Re: CMM jk billet front grab handles
« Reply #3 on: April 22, 2016, 01:01:45 PM »
Where are you moving the switches to? Mine are in the same location.

Welded cage or bolt together?
Jimbo
'13 True Blue JK

Offline kent10sne1

  • Visitor
  • Posts: 4791
  • KARMA : +37/-128
Re: CMM jk billet front grab handles
« Reply #4 on: April 22, 2016, 01:19:20 PM »
I was thinking / looking for a switch plate that would mount up on the bar or maybe on the lower left driver where the speaker is, or maybe under the AC control..its empty in that location.. 
Jeep Wrangler Sport JK 2012. //SKULL//
Kent Casey
37 PitBull Rocker's on ATX AX756 beadlock wheels
3.5FOX RESERVOIR COIL-OVER CONVERSION,5.13 Gears/Eaton Rear Locker
AtlasII 4.3.1 Dynatrac ProRock 44 Front Axle
MC Fenders & Sliders upgraded skids
http://www.gatrailriders.com/GTRForums/index.php/topic,15401.372.html

Offline Blue J

  • Visitor
  • Posts: 2758
  • KARMA : +19/-191
Re: CMM jk billet front grab handles
« Reply #5 on: April 22, 2016, 03:04:07 PM »
The spod panel will fit nicely on the dash center under the other switches.

http://www.4x4spod.com/category_s/12.htm

it would be nice if there was a way to mount the rugged ridge panel below the center switches.
Jimbo
'13 True Blue JK

 



BECOME A CORE MEMBER HERE

CHECK OUT OUR CLUB WEBSITE

JOIN US ON FACEBOOK

JOIN US ON INSTAGRAM