BECOME A CORE MEMBER HERE

Author Topic: Name That Part?  (Read 743 times)

Offline rabunjeeper

  • Visitor
  • Posts: 1198
  • KARMA : +0/-0
Name That Part?
« on: May 28, 2010, 09:27:04 AM »
See if anyone can figure out what I made these bumpstops out of.
If you all have been following my build thread then you know I asked the other day if anyone had any ideas on what I could use to make some front bump stops out of for my xj. I could have bought some hockey pucks but with shipping it was around 22 bucks, so I found this at Wal Mart for $1.00 a piece.


Offline Trailabite

  • GATR STAFF
  • *
  • Posts: 7627
  • KARMA : +12/-21
  • Need more parts!
    • Trailabite
Re: Name That Part?
« Reply #1 on: May 28, 2010, 09:55:19 AM »
It's a wutcha-ma-call-it.

Chuck & Sherry

*GET OUT OF KEVIN'S YARD*

Offline rabunjeeper

  • Visitor
  • Posts: 1198
  • KARMA : +0/-0
Re: Name That Part?
« Reply #2 on: May 28, 2010, 09:56:36 AM »
Close, it's a thing-a-ma-jig!

ranger11

  • Guest
Re: Name That Part?
« Reply #3 on: May 28, 2010, 11:56:55 AM »
A roller for a boat trailer? Maybe not since there isnt a hole in it. I will figure it out.
« Last Edit: May 28, 2010, 11:58:54 AM by Richard »

Offline rabunjeeper

  • Visitor
  • Posts: 1198
  • KARMA : +0/-0
Re: Name That Part?
« Reply #4 on: May 28, 2010, 11:58:54 AM »
The roller for a boat trailer?
No but I was looking for one of those when I was trying to find something to use!  {toast}

mdo817

  • Guest
Re: Name That Part?
« Reply #5 on: May 28, 2010, 12:34:45 PM »
It's a Hillbilly bump stop. {toast}

Offline rabunjeeper

  • Visitor
  • Posts: 1198
  • KARMA : +0/-0
Re: Name That Part?
« Reply #6 on: May 28, 2010, 12:37:35 PM »
It's a Hillbilly bump stop. {toast}

You callin me a hillbilly?  {:CH}
I'll give a hint, I cut the middle section out and what you see is the two ends. Also, it's made of rubber.
« Last Edit: May 28, 2010, 12:42:29 PM by rabunjeeper »

Offline Matt

  • Visitor
  • Posts: 8563
  • KARMA : +18/-38
  • ...
    • Georgia Trail Riders
Re: Name That Part?
« Reply #7 on: May 28, 2010, 12:40:40 PM »
A weight.

Maybe you should have let mike d. do some curls with it before you destroyed it.
« Last Edit: May 28, 2010, 12:43:44 PM by Matt »
Matt, Jessica, Aleigha (4), Gavin (1)

1999 Wrangler TJ
*With modifications

My '99 TJ Build

matt@gatrailriders.com

mdo817

  • Guest
Re: Name That Part?
« Reply #8 on: May 28, 2010, 12:42:24 PM »
It's a Hillbilly bump stop. {toast}

You callin me a hillbilly?  {:CH}
I'll give a hint, I cut the middle section out and what you see is the two ends.
It don't make you a bad person, I come from a long line of Hillbilly's, so yea I guess I was. {hihi}

Offline rabunjeeper

  • Visitor
  • Posts: 1198
  • KARMA : +0/-0
Re: Name That Part?
« Reply #9 on: May 28, 2010, 12:44:44 PM »
It's a Hillbilly bump stop. {toast}

You callin me a hillbilly?  {:CH}
I'll give a hint, I cut the middle section out and what you see is the two ends.
It don't make you a bad person, I come from a long line of Hillbilly's, so yea I guess I was. {hihi}
I might be a hillbilly, but at least they aint no bailing wire or duct tape on my Jeep!

mdo817

  • Guest
Re: Name That Part?
« Reply #10 on: May 28, 2010, 12:46:39 PM »
It's a Hillbilly bump stop. {toast}

You callin me a hillbilly?  {:CH}
I'll give a hint, I cut the middle section out and what you see is the two ends.
It don't make you a bad person, I come from a long line of Hillbilly's, so yea I guess I was. {hihi}
I might be a hillbilly, but at least they aint no bailing wire or duct tape on my Jeep!
It would hold that bump stop in. ;D

Offline rabunjeeper

  • Visitor
  • Posts: 1198
  • KARMA : +0/-0
Re: Name That Part?
« Reply #11 on: May 28, 2010, 12:49:11 PM »
Ha ha ha ha! I glued them to to the spring perch with liquid nails sub-floor construction adhesive! Hope that works.  {ehm}

 



BECOME A CORE MEMBER HERE

CHECK OUT OUR CLUB WEBSITE

JOIN US ON FACEBOOK

JOIN US ON INSTAGRAM