Georgia Trail Riders Forum
MEMBERS DISCUSSION AREA => General Discussion => Topic started by: Raisinhead on September 06, 2015, 09:17:05 PM
-
Post up some home projects that you take on. It's always a good feeling to get them accomplished.
I finally got one done that has been a long time coming.
Backyard Zip Line
It's about 145 feet long and moves
Used 13 - 15ft utility poles
1/2" cable
Robertson mini sr-71 (recommended by Mike from Harlan)
Several cable clamps
Heavy duty mobile home tie down stakes (auger ends)
Home made seat - 2x8 wood, cable, plastic sleeving
Wheel barrow tires
Pool noodle
Used the winch for two major parts of the project-helped pull a heavy ass pole up the hill and into up to go into the hole.
Cemented the poles about 4ft in the ground
Tied down with cable to the auger stakes
Tires drilled and used with the pool noodle for stopping
Used the winch again to get the line up and attached
Kids love it!!
(http://images.tapatalk-cdn.com/15/09/06/a8aa997de059275bdf8d998164349018.jpg)
(http://images.tapatalk-cdn.com/15/09/06/4cb712a86b28fce264e81d7d74c88201.jpg)
(http://images.tapatalk-cdn.com/15/09/06/60edd9a1fc5e69cbb0368ddb1cb104e5.jpg)
Sweet slow mo video
https://vimeo.com/138480698 (https://vimeo.com/138480698)
-
Cool! Can you ride it? :)
-
Cool! Can you ride it? :)
Oh yeah! It's over built a good bit. I rode it a few times before I let the kids get on.
-
Did paint and tile. Nothing exciting. Building a green egg stand now.
-
Zip line is killer Jay!!!
-
Man what a finish! Hang on tight.
-
Awesome project! House resale value just went up 10%!
Sent from my iPhone using Tapatalk
-
Zip line is killer Jay!!!
Thanks for the extra hand a few times!
Post up your sweet backyard project
-
Awesome project! House resale value just went up 10%!
Sent from my iPhone using Tapatalk
Haha, so did my insurance premium. Lol
-
Was a jeep used to pull that cable up?
-
Zip line idea is killer! //SLAMIN//. My kind of home improvement.
-
Was a jeep used to pull that cable up?
Yup. Pulled the pole up the hill and used for pulling the cable tight.
-
Built a backyard firepit 2 years ago. It's roughly 14' x 14' on the inside, dug in although not enough since it still has a slight slope to it. A good portion of the lumber was repurposed from left overs of the in-laws deck replacement which helped keep the cost down.
I didn't put in enough fill before I put in the pea gravel, so the gravel base ended up being too deep (about 4" when I was planning for 2"). Took 2 tons of gravel to fill in.
(http://i406.photobucket.com/albums/pp147/stf0412/Mobile%20Uploads/F35E18E3-3FCB-487C-9FEC-DEE2AC4CB39B_zpsy7sjqlf9.jpg)
(http://i406.photobucket.com/albums/pp147/stf0412/Mobile%20Uploads/C09B7556-9EED-4976-BA2E-DD8A3AE466BE_zpshthwinay.jpg)
(http://i406.photobucket.com/albums/pp147/stf0412/Mobile%20Uploads/10C244AC-2A10-4822-AD41-481EEB8586C6_zpsjhmdwuti.jpg)
-
Started this back in August I think... finished it this weekend. Custom pantry designed to my wife's specifications. Fun project and turned out awesome, but man it was a lot of work. I build everything, including the drawers. Joinery is primarily using the Festool Domino system. I don't have a tablesaw, but used a Festool tracksaw to cut all the sheetgoods...
(http://i1197.photobucket.com/albums/aa431/jaredc79/77271613-F594-4586-A058-06CD201553FB.jpg) (http://s1197.photobucket.com/user/jaredc79/media/77271613-F594-4586-A058-06CD201553FB.jpg.html)
(http://i1197.photobucket.com/albums/aa431/jaredc79/7E7A4C61-3E4E-44D5-81F7-0A69371765BC.jpg) (http://s1197.photobucket.com/user/jaredc79/media/7E7A4C61-3E4E-44D5-81F7-0A69371765BC.jpg.html)
(http://i1197.photobucket.com/albums/aa431/jaredc79/67859C42-CF23-4C68-B434-D1A6B2F65EC7.jpg) (http://s1197.photobucket.com/user/jaredc79/media/67859C42-CF23-4C68-B434-D1A6B2F65EC7.jpg.html)
-
^^^nice work
-
That is awesome. Fantastic craftsmanship.
Sent from my iPhone using Tapatalk
-
Awesome, Jared. What I'm most impressed with is your ability to get requirements (useful ones) out of the client.
I'm secondarily impressed with the workmanship, but that's just because I've seen you work on other things.
- Torg
-
Well done Jared.
-
Very nice, if i ever did this for my wife, she would shoot me and then have the police start an investigation looking into the true identity of the person that did this for her. LOL
all joking aside, im impressed. great job.
-
Jared, upon further review, I have some concerns and praise: 1) Mixing bean types in the storage container...not good; 2) Books are supposed to be vertical (on the side damages the binding); 3) as I've told you many times, I am a fan of the selection your nuts provide so keep up the good work.
-
Jared, upon further review, I have some concerns and praise: 1) Mixing bean types in the storage container...not good; 2) Books are supposed to be vertical (on the side damages the binding); 3) as I've told you many times, I am a fan of the selection your nuts provide so keep up the good work.
I am familiar with the type of client Jared was working with. I have done work for a very similar client, many many times. I can tell you that you have no control over how the product is used after completion...that is not a decision for the lowly contractor.
I made this mistake a looooong time ago; first home project requested by client. Client said she would hire an "outside" contractor, me(inside contractor) said no "i'll do it" and proceeded to do a killer job. Now the Client thinks anything she can think of or read about in a magazine or TV show can me magically constructed by said inside contractor. Big mistake. Should have F'd up the first project and had a lot more time for fixing my jeep and wheeling
@jc79 very nice work and I like your style. Put out a quality project but it took a number of months...that may or may not be enough to keep you from other projects.
-
Great points Tony. I have also been contracted to do jobs for a similar client. My cost vs. "outside contractor" cost is always exponentially lower, but the client never cares about cost.
-
I am glad I am in construction and just tell the subs what to do.
-
Funny stuff... Clark, appreciate your continued focus on my nuts. The attention never gets old.
Tony, its a delicate dance. I need to keep her happy enough that I can keep justifying new tools... but not be working like a have a second job.
Thanks for the comments, guys!
-
Forgot about this thread
last summer turned this:
(http://i221.photobucket.com/albums/dd273/tchaap_2007/Back%20Porch%20project%202014/57413D98-1D57-488A-B6A1-1BE802531F15.jpg)
into this:
(http://i68.photobucket.com/albums/i32/TChaap/Outdoor%20Kitchen/GOPR0005_zps5a7c9b65.jpg)
(http://i68.photobucket.com/albums/i32/TChaap/Outdoor%20Kitchen/CB120080-9981-4C8B-AEA5-B82F150DE01F_zps9npbtrrv.jpg)
This Summer and Fall I turned this:
(http://i221.photobucket.com/albums/dd273/tchaap_2007/fire%20pit%202015/78C938AA-381B-44AF-85F1-94868D907DB4.jpg)
into this:
(http://i221.photobucket.com/albums/dd273/tchaap_2007/fire%20pit%202015/E4369488-A6D8-4C21-88D5-7A0A5044FDA7.jpg)
(http://i221.photobucket.com/albums/dd273/tchaap_2007/fire%20pit%202015/5E0B7F79-698B-4384-84B4-3BDEAC7C9066.jpg)
(http://i221.photobucket.com/albums/dd273/tchaap_2007/fire%20pit%202015/34FC2DC3-73AC-4917-AEF5-4296159C7DA3.jpg)
-
Said projects always cause stress between client and amatuer contractor, and client may stop all ancillary communication and maintenance agreement payments until project is complete with 100% satisfaction. This time period can be agonizing and last much longer than anticipated.
So I have no time for those projects anymore so we hire a pro with the right tools rather than buying all of them for one use usually and he does it right the first time, instead of me wasting materials and ending up costing about the same. I probably have every tool in the basement. So I come home and its all done and she is happy to see me.
-
Said projects always cause stress between client and amatuer contractor, and client may stop all ancillary communication and maintenance agreement payments until project is complete with 100% satisfaction. This time period can be agonizing and last much longer than anticipated.
So I have no time for those projects anymore so we hire a pro with the right tools rather than buying all of them for one use usually and he does it right the first time, instead of me wasting materials and ending up costing about the same. I probably have every tool in the basement. So I come home and its all done and she is happy to see me.
Never a problem with us. She gets exactly what she wants without a stranger in the house. I get time to enjoy a hobby and can fund some tool purchases. Win win!
Sent from my iPhone using Tapatalk
-
very nice. How do you like that stand up heater? Justin has one similar and he says it cranks out some heat
-
Nice deck, DP!
-
Very nice, Don! I need a new deck...wanna build the same thing, but about 12' in the air? I will not be building my own deck.
-
Here are a few oldies from last year.
Before
(http://uploads.tapatalk-cdn.com/20160119/2c0e4ae8cb53136f4b7728a70ed87445.jpg)
After (only backsplash and wine fridge were diy)
(http://uploads.tapatalk-cdn.com/20160119/3b626c61676f394be6bf4c731b7f57fa.jpg)(http://uploads.tapatalk-cdn.com/20160119/421a2cf50507e68bb7d4d98d82a6cdc6.jpg)
Sunroom floor - before (previous owner furniture, etc)
(http://uploads.tapatalk-cdn.com/20160119/73a586d66ed10f8c6de9c9bdcda8b1f5.jpg)
(http://uploads.tapatalk-cdn.com/20160119/1f5450d44c1691c8ad55d91231a6ebe1.jpg)
(http://uploads.tapatalk-cdn.com/20160119/1ad53c4f32ff120c2c13dea08628ee5e.jpg)
Doors
(http://uploads.tapatalk-cdn.com/20160119/22013ca993d16155ce9fa4ad83264810.jpg)
(http://uploads.tapatalk-cdn.com/20160119/8681e2cd3ded5a173178f7fc8877fc67.jpg)
-
Very nice, Don! I need a new deck...wanna build the same thing, but about 12' in the air? I will not be building my own deck.
Yes, Don that deck is sweet!
-
^^those sliding doors are killer
and the kitchen was freaking transformation. I forgot how it looked.
-
^^those sliding doors are killer
and the kitchen was freaking transformation. I forgot how it looked.
Any time my client starts to complain about quickness or project completion, I always show this before and afters.
Your backyard is what my backyard wants to be when it grows up.
-
^^those sliding doors are killer
Those style of doors are on my to-do list for the bedroom conversion downstairs...any details you can share?
- Torg
-
^^those sliding doors are killer
Those style of doors are on my to-do list for the bedroom conversion downstairs...any details you can share?
- Torg
@raisinhead
- Torg
-
^^those sliding doors are killer
Those style of doors are on my to-do list for the bedroom conversion downstairs...any details you can share?
- Torg
I can tell you what I did.
We got a steal on the doors off of CL. They were from a Brooklyn Brownstone. We were going to sand and stain, but the holes from the hardware were too tough to cover. We had a company that did some furniture for us paint and stain them. Used artisan hardware for the sliding hardware. (Probably a cheaper alternative to build some from tractor supply, but I didn't mind since we did so well on everything else). The handles were from Van Dyke...?
Tony helped me hang them.
-
(http://uploads.tapatalk-cdn.com/20160220/cc2994e5fced5f1c5d9a9bd0cea65f5e.jpg)
-
Here's the guy I go to for lawnmower repairs. I think he does other small gas engines as well:
https://www.google.com/webhp?sourceid=chrome-instant&ion=1&espv=2&ie=UTF-8#q=billy%27s%20small%20engine%20repair (https://www.google.com/webhp?sourceid=chrome-instant&ion=1&espv=2&ie=UTF-8#q=billy%27s%20small%20engine%20repair)
-
This was a little closet project to enclose our water heater in the basement after I moved it, but it turned into a little more.. I had the old barn wood, bought the tv used for cheap, and did the bartop ourselves with cabinet grade plywood.. The backside of the bar is old used kitchen cabinets we got free that I jacked up to bar height.. the right side is open underneath and is awaiting my kegerator setup with a double tap head.. Just waiting on the local bottle shop to turn their old inventory and sell me a setup one used on the cheap.
(http://i1096.photobucket.com/albums/g324/shiftmx47/Mobile%20Uploads/IMG_20160123_195556857.jpg) (http://s1096.photobucket.com/user/shiftmx47/media/Mobile%20Uploads/IMG_20160123_195556857.jpg.html)
it was basically an unused drive in basement till we did all this over the last few months, not in the pic is the pool table, futon, and new to us wood stove. Cool little hangout spot for the dogs basically.. they like to party.
-
Very nice Justin, but because I have to bust your balls...good job not enclosing the HVAC
- Torg
-
Very nice Justin, but because I have to bust your balls...good job not enclosing the HVAC
- Torg
balls busted.. when you are drunk and playing pool or watching the game its really not that noticeable.. ass..
-
Very nice Justin, but because I have to bust your balls...good job not enclosing the HVAC
- Torg
I don't think code will allow you to enclose the HVAC without leaving like 2' on each side to get to it....but knowing Justin, code should not apply.
-
Very nice Justin, but because I have to bust your balls...good job not enclosing the HVAC
- Torg
I don't think code will allow you to enclose the HVAC without leaving like 2' on each side to get to it....but knowing Justin, code should not apply.
i honestly appreciate that comment @tcdawg , and yes, their silly codes do not apply to my bar. Although I actually did do the responsible thing and let State Farm know about it and come take pics for the proper paper work because of the wood heater install.
-
Some damn good work on here!! Impressive!
-
Our house does not have a real pantry, only an extra deep cabinet on the end. It is adequate for space but you can never reach the stuff at the back or it gets put back there and since you can't see it we forget about it.
So I had been meaning to make slide out drawers for awhile. Finally got them done. The only real cost was the slides off amazon and wood fronts and backs. The drawer bottoms I had some left over 1/4 plywood from my sister's kitchen renovation. I also had enough stain leftover front a previous furniture refinish job that was a close enough match.
(http://i406.photobucket.com/albums/pp147/stf0412/Mobile%20Uploads/0C4A3F37-2F2A-42CB-8247-535B69C41B37_zpsaaxbywoy.jpg) (http://s406.photobucket.com/user/stf0412/media/Mobile%20Uploads/0C4A3F37-2F2A-42CB-8247-535B69C41B37_zpsaaxbywoy.jpg.html)
(http://i406.photobucket.com/albums/pp147/stf0412/Mobile%20Uploads/545E12D1-CFE2-463F-849C-D93900B4B7F8_zpsq8hpyb72.jpg) (http://s406.photobucket.com/user/stf0412/media/Mobile%20Uploads/545E12D1-CFE2-463F-849C-D93900B4B7F8_zpsq8hpyb72.jpg.html)
-
Very nice, Scott. But you're still leave stuff at the back and forget about it. ;) hopefully just less stuff.
- Torg
-
Projects look great.
I have got steps to build off a floating deck, and then redo most of bathroom. Going to rip out the shower insert to put in all tile and frame less glass door. Carry the tile around the shower. Repaint. I have tiled the floor a while back.
-
Our house does not have a real pantry, only an extra deep cabinet on the end. It is adequate for space but you can never reach the stuff at the back or it gets put back there and since you can't see it we forget about it.
So I had been meaning to make slide out drawers for awhile. Finally got them done. The only real cost was the slides off amazon and wood fronts and backs. The drawer bottoms I had some left over 1/4 plywood from my sister's kitchen renovation. I also had enough stain leftover front a previous furniture refinish job that was a close enough match.
(http://i406.photobucket.com/albums/pp147/stf0412/Mobile%20Uploads/0C4A3F37-2F2A-42CB-8247-535B69C41B37_zpsaaxbywoy.jpg) (http://s406.photobucket.com/user/stf0412/media/Mobile%20Uploads/0C4A3F37-2F2A-42CB-8247-535B69C41B37_zpsaaxbywoy.jpg.html)
(http://i406.photobucket.com/albums/pp147/stf0412/Mobile%20Uploads/545E12D1-CFE2-463F-849C-D93900B4B7F8_zpsq8hpyb72.jpg) (http://s406.photobucket.com/user/stf0412/media/Mobile%20Uploads/545E12D1-CFE2-463F-849C-D93900B4B7F8_zpsq8hpyb72.jpg.html)
Solid!!!!
-
Glad to see the peanut butter is easily accessible. Looks great!
-
Glad to see the peanut butter is easily accessible. Looks great!
Yep, critical.
-
My painter finally had a free minute to paint the garage art work I won last year at CFR 16' !!!
-
My painter finally had a free minute to paint the garage art work I won last year at CFR 16' !!!
Damn
That came out killer!
-
Nice
-
Awesome job on that sign.
- Torg
-
That's awesome
-
Cool
-
//SLAMIN// the paint job made that look great! Should we start a garage wall art thread.... //LMAO//
-
Put it in NSFW
- Torg
-
Put it in NSFW
- Torg
//SLAMIN// the paint job made that look great! Should we start a garage wall art thread.... //LMAO//
Those posts are related.
- Torg
-
That sign looks killer.
-
Renee made these fishing rod holders for me and my son(http://uploads.tapatalk-cdn.com/20160502/498c028ddd62f4c48ffa8e52ab59edfe.jpg)(http://uploads.tapatalk-cdn.com/20160502/029be5d2d5cba8589b0027680ebc03ef.jpg)
Sent from my iPhone using Tapatalk
-
Nifty!
Sent from my XT1254 using Tapatalk
-
Nice
Sent from my iPhone using Tapatalk
-
I added another set of steps at my daughters
house so my granddaughters can get to the
playset without going around the other end
of the porch.
(http://i898.photobucket.com/albums/ac182/tjsahara00/misc/porch%20steps-3_zpsapvwzxek.jpg) (http://s898.photobucket.com/user/tjsahara00/media/misc/porch%20steps-3_zpsapvwzxek.jpg.html)
(http://i898.photobucket.com/albums/ac182/tjsahara00/misc/porch%20steps-1_zpsyhijfkpd.jpg) (http://s898.photobucket.com/user/tjsahara00/media/misc/porch%20steps-1_zpsyhijfkpd.jpg.html)
(http://i898.photobucket.com/albums/ac182/tjsahara00/misc/porch%20steps-2_zpsni0tonha.jpg) (http://s898.photobucket.com/user/tjsahara00/media/misc/porch%20steps-2_zpsni0tonha.jpg.html)
-
Ah, convenience...I love it ;)
Sent from my XT1254 using Tapatalk
-
Well the oldest is 3 and the other end of the porch is
at the drive way where they park so it was a no brainer
-
Bringing up an old thread.
I can’t get the buggy done because I seem to have to many other projects in the way. We have a basement room that is going to be a craft room for Katie. It was already partially finished so I thought 3-4 days work, no problem.
Almost two weeks later I am wrapping it up. It had hideous wall paper that we took down...which of course damaged the drywall paper. So, sealing, skim coat, removing the nasty drop ceiling, moving the ductwork back to the wall, adding drywall up to the new ceiling height, and then sanding and painting everything. It’s only a 12 x 13 ft room but I’m exhausted. I need to stick to metal fabrication!
Here are some before pics:
(https://i.imgur.com/IruwAV1.jpg)
(https://i.imgur.com/XhjuaRX.jpg)
(https://i.imgur.com/IruwAV1.jpg)
During pics:
(https://i.imgur.com/CP4plm9.jpg)
(https://i.imgur.com/asZRWq8.jpg)
(https://i.imgur.com/MyYtn3X.jpg)
(https://i.imgur.com/UkyMBNu.jpg)
And after pics. Still have one more coat to put on the concrete and to hang the painted doors back up.
(https://i.imgur.com/zTLsXm1.jpg)
(https://i.imgur.com/ruNLcKn.jpg)
(https://i.imgur.com/jhKo6nT.jpg)
-
Nice work, Scott. Looking good.
-
Looks very nice. What's the lighting situation gonna be?
Sent from my SM-G960U using Tapatalk
-
Very nice work Scott.
-
Anything worth doing is worth doing correctly the 1st time.
That looks like 2 weeks of hard work.
Well Done!
-
I just cut the last pine tree on my property on Saturday. Now I have 28 more large stumps to get up and about twice as many smaller 12" or smaller stumps to get up before I can level the ground out and start seeding grass. I am going to take a break from this on about 12-14 days and finish the jeep.
I am working this tractor like it owes me money!
-
nice work Larry
-
Awesome stuff!!! I wish I had the land, money, and time to do that fun stuff.
-
Nice work Larry and Scott!
I’m feeling the same, several projects going and it’s cutting into space.
-
Nice Larry! Removing stumps that size will test your determination for sure. You are working that tractor hard!
-
Looks very nice. What's the lighting situation gonna be?
Sent from my SM-G960U using Tapatalk
I have a new 8ft fixture (4x 4ft tubes) but the wife said that would be overkill. We will probably just add som sort of 4ft LED fixture.
-
Looks very nice. What's the lighting situation gonna be?
Sent from my SM-G960U using Tapatalk
I have a new 8ft fixture (4x 4ft tubes) but the wife said that would be overkill. We will probably just add som sort of 4ft LED fixture.
you can't ever have too much light...as a wise person has stated, "there's no kill like overkill".
-
More of why I haven’t finished my buggy project yet.
Chickenville- established June 2020
We are at 7 chickens right now. We will see if that number goes up or down.
(https://i.imgur.com/TKNYKWx.jpg)
(https://i.imgur.com/93AQ61q.jpg)
(https://i.imgur.com/u7oduv8.jpg)
-
More of why I haven’t finished my buggy project yet.
Chickenville- established June 2020
We are at 7 chickens right now. We will see if that number goes up or down.
(https://i.imgur.com/TKNYKWx.jpg)
(https://i.imgur.com/93AQ61q.jpg)
(https://i.imgur.com/u7oduv8.jpg)
Awesome, fresh 's
Sent from my SM-G975U using Tapatalk
-
That’s awesome. How many of them can ride the scooter?
-
More of why I haven’t finished my buggy project yet.
Chickenville- established June 2020
We are at 7 chickens right now. We will see if that number goes up or down.
(https://i.imgur.com/TKNYKWx.jpg)
(https://i.imgur.com/93AQ61q.jpg)
(https://i.imgur.com/u7oduv8.jpg)
I sure do love chicken wings
-
This is what I've been killing myself with while on leave.(https://uploads.tapatalk-cdn.com/20200619/b148195a58583f060d73b38915704890.jpg)(https://uploads.tapatalk-cdn.com/20200619/99261191b7d85059ee36c7b6f38eb08a.jpg)(https://uploads.tapatalk-cdn.com/20200619/b924ab17f4b45569485769bc3fec347d.jpg)(https://uploads.tapatalk-cdn.com/20200619/7db0190d826244fbdd338153a6f193db.jpg)(https://uploads.tapatalk-cdn.com/20200619/da8ce40ce07cabee1630966390daaf48.jpg)
Sent from my SM-N960U using Tapatalk
-
This is what I've been killing myself with while on leave.(https://uploads.tapatalk-cdn.com/20200619/b148195a58583f060d73b38915704890.jpg)(https://uploads.tapatalk-cdn.com/20200619/99261191b7d85059ee36c7b6f38eb08a.jpg)(https://uploads.tapatalk-cdn.com/20200619/b924ab17f4b45569485769bc3fec347d.jpg)(https://uploads.tapatalk-cdn.com/20200619/7db0190d826244fbdd338153a6f193db.jpg)(https://uploads.tapatalk-cdn.com/20200619/da8ce40ce07cabee1630966390daaf48.jpg)
Sent from my SM-N960U using Tapatalk
I need to do this to my backyard.
Sent from my SM-G975U using Tapatalk
-
That’s awesome. How many of them can ride the scooter?
Haha, not sure maybe as the chicks grow up they wil pick up some talents other than just laying eggs and pooping everywhere.
-
@zrxmopar looks like you are going to have a much bigger parking pad when you are done [cheers]
-
More of why I haven’t finished my buggy project yet.
Chickenville- established June 2020
We are at 7 chickens right now. We will see if that number goes up or down.
(https://i.imgur.com/TKNYKWx.jpg)
(https://i.imgur.com/93AQ61q.jpg)
(https://i.imgur.com/u7oduv8.jpg)
I sure do love chicken wings
Me too. And a good chicken pot pie is always nice.
-
Birthday card my wife purchased for a friend's:
"I dream of a world where a chicken can cross the road without someone questioning its motives."
-
Birthday card my wife purchased for a friend's:
"I dream of a world where a chicken can cross the road without someone questioning its motives."
Here, here!
Sent from my iPhone using Tapatalk Pro
-
More of why I haven’t finished my buggy project yet.
Chickenville- established June 2020
We are at 7 chickens right now. We will see if that number goes up or down.
(https://i.imgur.com/TKNYKWx.jpg)
(https://i.imgur.com/93AQ61q.jpg)
(https://i.imgur.com/u7oduv8.jpg)
Be careful!
One person has died and 465 people have gotten sick after interacting with pet poultry
https://www.cnn.com/2020/06/24/health/salmonella-backyard-chickens/index.html
Sent from my SM-G960U using Tapatalk
-
More of why I haven’t finished my buggy project yet.
Chickenville- established June 2020
We are at 7 chickens right now. We will see if that number goes up or down.
(https://i.imgur.com/TKNYKWx.jpg)
(https://i.imgur.com/93AQ61q.jpg)
(https://i.imgur.com/u7oduv8.jpg)
Be careful!
One person has died and 465 people have gotten sick after interacting with pet poultry
https://www.cnn.com/2020/06/24/health/salmonella-backyard-chickens/index.html
Sent from my SM-G960U using Tapatalk
Maybe get the chickens to wear masks and stand 6 ft apart?
-
More of why I haven’t finished my buggy project yet.
Chickenville- established June 2020
We are at 7 chickens right now. We will see if that number goes up or down.
[img width=1024 height=768]ht
[img width
[img width=1024 height=768]
Be careful!
One person has died and 465 people have gotten sick after interacting with pet poultry
https://www.cnn.com/2020/06/24/health/salmonella-backyard-chickens/index.html
Sent from my SM-G960U using Tapatalk
Maybe get the chickens to wear masks and stand 6 ft apart?
lmao
-
I added a new 4x4 to my stable this past week. Maybe we should all be building our rigs to be more like tractors. This has standard tractor stuff like a factory rear locker and cutting brakes.
This should help for future projects around the yard.
-
I added a new 4x4 to my stable this past week. Maybe we should all be building our rigs to be more like tractors. This has standard tractor stuff like a factory rear locker and cutting brakes.
This should help for future projects around the yard.
Damn dude! Super jealous
-
Very nice....would love to have something like that!
-
Nice. Had a 4000 series Kubota once that had we not finally gotten new equipment was going to roll the hour meter back to 0, had 9900+ hours on it. Should last you a long time!
Sent from my iPhone using Tapatalk
-
Nice toy
-
What model, Scott? I’ve had an L2501 for four years now and its great. Can’t calculate how much rock, dirt and snow it’s moved in that time.
I couldn’t justify the backhoe though...
A set of forks is money well spent and I use them all the time.
Sent from my iPhone using Tapatalk
-
Awesome
toy tool! I really don't have a use for it, but I want one.
-
I added a new 4x4 to my stable this past week. Maybe we should all be building our rigs to be more like tractors. This has standard tractor stuff like a factory rear locker and cutting brakes.
This should help for future projects around the yard.
Epic
-
What model, Scott? I’ve had an L2501 for four years now and its great. Can’t calculate how much rock, dirt and snow it’s moved in that time.
I couldn’t justify the backhoe though...
A set of forks is money well spent and I use them all the time.
Sent from my iPhone using Tapatalk
Jared- it’s an L2501. I ended up going with the HST. What did transmission do you have?
The non two stage clutch or non live PTO was the deal breaker for the gear drive for me. I would prefer the gear drive for everything else but bush hogging.
I grabbed a 5 foot rotary cutter, a tiller for the wife’s garden, and a set of pallet forks. Having the skid Steelers quick attach bucket is awesome!
-
haha, i figured based on the loader model it might be. I liked that the 2501 falls below the HP requirement to require the DPF.
I also have the HST. Tractor doing tractor stuff...
(https://uploads.tapatalk-cdn.com/20201005/4819b17fa39921adb7a86e2ab5bffeef.jpg)
(https://uploads.tapatalk-cdn.com/20201005/f8af3484cf22f5e48b906ab27674c4ae.jpg)
(https://uploads.tapatalk-cdn.com/20201005/e6331775a3bf06fdd62e1a3baac4ca0f.jpg)
-
haha, i figured based on the loader model it might be. I liked that the 2501 falls below the HP requirement to require the DPF.
I also have the HST. Tractor doing tractor stuff...
(https://uploads.tapatalk-cdn.com/20201005/4819b17fa39921adb7a86e2ab5bffeef.jpg)
(https://uploads.tapatalk-cdn.com/20201005/f8af3484cf22f5e48b906ab27674c4ae.jpg)
(https://uploads.tapatalk-cdn.com/20201005/e6331775a3bf06fdd62e1a3baac4ca0f.jpg)
You'll be able to share some snow plowing pics soon.
-
Here you go, Chuck...
(https://uploads.tapatalk-cdn.com/20201005/7ae5aa346c7f48c8c64a5de333523e6c.jpg)
Sent from my iPhone using Tapatalk
-
haha, i figured based on the loader model it might be. I liked that the 2501 falls below the HP requirement to require the DPF.
I also have the HST. Tractor doing tractor stuff...
(https://uploads.tapatalk-cdn.com/20201005/f8af3484cf22f5e48b906ab27674c4ae.jpg)
Chuck, tell me more about that wood hauler attachment: What manufacturer? Made in 'merca?
Seriously, more pictures of that thing, good sir.
-
haha, i figured based on the loader model it might be. I liked that the 2501 falls below the HP requirement to require the DPF.
I also have the HST. Tractor doing tractor stuff...
(https://uploads.tapatalk-cdn.com/20201005/f8af3484cf22f5e48b906ab27674c4ae.jpg)
Chuck, tell me more about that wood hauler attachment: What manufacturer? Made in 'merca?
Seriously, more pictures of that thing, good sir.
Doug,
Here are two short videos, my oldest taking a ride and the wife taking a joyride on the tractor the day we got it.
/>
-
Just like any good grown up toy, it has a lot of options for accessories and upgrades!
(https://i.imgur.com/OnJwksj.jpg)
(https://i.imgur.com/wEGGT7z.jpg)
(https://i.imgur.com/Fy27g1J.jpg)
-
Chuck, tell me more about that wood hauler attachment: What manufacturer? Made in 'merca?
Seriously, more pictures of that thing, good sir.
Jay, I'll have to get some pics but this is what I bought:
https://www.tractorsupply.com/tsc/product/countyline-carry-all
Clearly you build the platform to your needs. Some guys build them out a lot nicer than mine:
(https://www.tractorbynet.com/forums/files/build-yourself/588637d1548377879-build-your-own-3-point-img_5033-copy-jpg)
-
haha, i figured based on the loader model it might be. I liked that the 2501 falls below the HP requirement to require the DPF.
I also have the HST. Tractor doing tractor stuff...
(https://uploads.tapatalk-cdn.com/20201005/f8af3484cf22f5e48b906ab27674c4ae.jpg)
Chuck, tell me more about that wood hauler attachment: What manufacturer? Made in 'merca?
Seriously, more pictures of that thing, good sir.
I can't tell you anything about it man.
-
Chuck, tell me more about that wood hauler attachment: What manufacturer? Made in 'merca?
Seriously, more pictures of that thing, good sir.
Jay, I'll have to get some pics but this is what I bought:
https://www.tractorsupply.com/tsc/product/countyline-carry-all
Clearly you build the platform to your needs. Some guys build them out a lot nicer than mine:
(https://www.tractorbynet.com/forums/files/build-yourself/588637d1548377879-build-your-own-3-point-img_5033-copy-jpg)
Very cool, Frank.
Sent from my SM-G960U using Tapatalk
-
Why unload empty pallets by hand when you can spend three times as long getting out the tractor and doing it that way.
(https://i.imgur.com/2pNNxoI.jpg)
-
Lol...so much better using the correct tool for the job.
Sent from my SM-G960U using Tapatalk
-
Even better if the bucket was on it to begin with, and you had to swap on the forks. But yeah, life is better when using hydraulics!
-
Almost done with this cooler stand.
-
Over the years I've accumulated all kind of tools in different small tool boxes. Time to get them organized so I bought a Husky tool box....
51" wide 64'' tall with the lid closed
-
Over the years I've accumulated all kind of tools in different small tool boxes. Time to get them organized so I bought a Husky tool box....
51" wide 64'' tall with the lid closed
I think that’s a new one from Husky. I looked at it just last weekend. Super nice.
-
Over the years I've accumulated all kind of tools in different small tool boxes. Time to get them organized so I bought a Husky tool box....
51" wide 64'' tall with the lid closed
I love the matte black! Nice choice
-
Supposed to be professional grade..
Really nice....great reviews. Got it already put together. I decide to pick it up on my trailer. Glad I need...it's pretty heavy.
-
Almost done with this cooler stand.
Larry- is that pallet wood?
-
@tjsahara00 upgrading to a larger tool box is always a good idea! Especially if you buy a box bigger than you need. Then you get to buy more tools to fill it up properly. [cheers]
-
Almost done with this cooler stand.
Larry- is that pallet wood?
Looks like it. I just grabbed 15 from a buddy to have for future projects. I like the cooler table idea for them.
Sent from my iPhone using Tapatalk
-
Over the years I've accumulated all kind of tools in different small tool boxes. Time to get them organized so I bought a Husky tool box....
51" wide 64'' tall with the lid closed
I saw this item on the 'black friday sale' list. If you paid more than $798, you might be able to get some money back.
https://www.homedepot.com/p/Husky-Industrial-52-in-W-x-21-5-in-D-15-Drawer-Tool-Chest-and-Rolling-Cabinet-Combo-with-LED-Light-in-Matte-Black-H52CH6TR9HDV3/309210140
-
Almost done with this cooler stand.
Larry- is that pallet wood?
Yes sir. I added a bottle opener, catch bin, and handle.
-
Almost done with this cooler stand.
Larry- is that pallet wood?
Yes sir. I added a bottle opener, catch bin, and handle.
Catch bin for the win!
-
my chipper just got delivered yesterday, in time for the cold weather and no desire to put it together and use it now. Not sure if that is a project or not, clean up project.
-
my chipper just got delivered yesterday, in time for the cold weather and no desire to put it together and use it now. Not sure if that is a project or not, clean up project.
Which chipper did you go with?
Mine has been a beast, but changing the blade is a PITA.
Sent from my SM-G960U using Tapatalk
-
I am getting started on my lean-to projects. One going on the side of the shop (12ft x 40ft) and one going on the back of the shop (13 x 28ft).
The power company left me a telephone pole awhile back. I chopped it into thirds and that is my posts for the back lean to. That saved me about $150 as 6x6s run $50 a piece and making laminated posts is about the same.
(https://i.imgur.com/oCCju1V.jpg)
Here is the boss man inspecting my post hole digging.
(https://i.imgur.com/ZqcJYTD.jpg)
(https://i.imgur.com/M46zuSE.jpg)
(https://i.imgur.com/x12dpXI.jpg)
-
no auger attachment on the tractor? tisk tisk
-
The struggle is real!
-
I hope you took the opportunity to show boss man how to use a post hole digger and have him try it out.
-
my chipper just got delivered yesterday, in time for the cold weather and no desire to put it together and use it now. Not sure if that is a project or not, clean up project.
Which chipper did you go with?
Mine has been a beast, but changing the blade is a PITA.
Sent from my SM-G960U using Tapatalk
I bought way more than needed, well that isn't true, could use more. But a HD 45% off sale made me do it.
heck, its still on sale. https://www.homedepot.com/p/Brush-Master-5-25-x-3-75-in-445cc-Gas-Powered-Self-Feed-Chipper-Shredder-with-Unique-Innovation-3-in-1-Discharge-Gloves-Goggles-CH10M20/311938217
hoping I can use it for a couple years and not loose too much value. Or just start renting it out soon.
-
my chipper just got delivered yesterday, in time for the cold weather and no desire to put it together and use it now. Not sure if that is a project or not, clean up project.
Which chipper did you go with?
Mine has been a beast, but changing the blade is a PITA.
Sent from my SM-G960U using Tapatalk
I bought way more than needed, well that isn't true, could use more. But a HD 45% off sale made me do it.
heck, its still on sale. https://www.homedepot.com/p/Brush-Master-5-25-x-3-75-in-445cc-Gas-Powered-Self-Feed-Chipper-Shredder-with-Unique-Innovation-3-in-1-Discharge-Gloves-Goggles-CH10M20/311938217
hoping I can use it for a couple years and not loose too much value. Or just start renting it out soon.
Very nice! I have a Brush Master, and paid about the same as the discounted price a few years ago, but it can't handle limbs that big. The engine has been tops, and besides the blades needing to be changed/sharpened frequently, it hasn't needed any special attention. I've been using it a lot this year.
Good job on getting a good deal on a big machine. My next one will be an Asplundh-like model :)
(https://encrypted-tbn0.gstatic.com/images?q=tbn:ANd9GcSka_WFdu6tEx97caicGIkJ4g1oB72Q84S82g&usqp=CAU)
-
Good thing about multiple acres is dragging limbs
off to fill in gully's and such. No need for a chipper.
-
Good thing about multiple acres is dragging limbs
off to fill in gully's and such. No need for a chipper.
Amen...I want that life so much!
Sent from my SM-G960U using Tapatalk
-
as long at it can do smaller sub 2-3" inch limbs, that will be great. its really just trying to keep the acre or so cleaned up and not rent a larger chipper for couple days at close to what I paid for this chipper.
-
as long at it can do smaller sub 2-3" inch limbs, that will be great. its really just trying to keep the acre or so cleaned up and not rent a larger chipper for couple days at close to what I paid for this chipper.
Yeah, mine is for 3" round, and it'll do every bit of 3". Bigger than 2.5" I usually set aside for camping firewood. Since yours can do 5x3" you will have no problem, and thta size will save you from having to buck the limbs as much as I have to...such a PITA.
-
as long at it can do smaller sub 2-3" inch limbs, that will be great. its really just trying to keep the acre or so cleaned up and not rent a larger chipper for couple days at close to what I paid for this chipper.
Yeah, mine is for 3" round, and it'll do every bit of 3". Bigger than 2.5" I usually set aside for camping firewood. Since yours can do 5x3" you will have no problem, and thta size will save you from having to buck the limbs as much as I have to...such a PITA.
hoping it will do the little bit larger sizes as well. I do need to put it together, it came in a big box. hoping to get it put together some time in the next few days. I have a big pile of stuff just waiting on my patio ready to be put through the machine. that and a hillside to start tackling.
Not as much fun as getting the garage together so I can get the LJ up and running.
-
as long at it can do smaller sub 2-3" inch limbs, that will be great. its really just trying to keep the acre or so cleaned up and not rent a larger chipper for couple days at close to what I paid for this chipper.
I get my money's worth out of living in the city limits and paying city taxes. No wood chipper for me, dump it in the ditch and I am done. City pick's up twice a week.
-
as long at it can do smaller sub 2-3" inch limbs, that will be great. its really just trying to keep the acre or so cleaned up and not rent a larger chipper for couple days at close to what I paid for this chipper.
I get my money's worth out of living in the city limits and paying city taxes. No wood chipper for me, dump it in the ditch and I am done. City pick's up twice a week.
I can do that as well, they just need to be a certain size. I really just wanted a chipper/shredder to reduct the number of bags needed for the smaller stuff. The larger chipper was just a price performer.
-
as long at it can do smaller sub 2-3" inch limbs, that will be great. its really just trying to keep the acre or so cleaned up and not rent a larger chipper for couple days at close to what I paid for this chipper.
I get my money's worth out of living in the city limits and paying city taxes. No wood chipper for me, dump it in the ditch and I am done. City pick's up twice a week.
My city would never accept those. Have to be less than 2" diameter and 4' length...and debris has to be bagged...ugh, it's like they don't want to do the work :)
-
as long at it can do smaller sub 2-3" inch limbs, that will be great. its really just trying to keep the acre or so cleaned up and not rent a larger chipper for couple days at close to what I paid for this chipper.
I get my money's worth out of living in the city limits and paying city taxes. No wood chipper for me, dump it in the ditch and I am done. City pick's up twice a week.
My city would never accept those. Have to be less than 2" diameter and 4' length...and debris has to be bagged...ugh, it's like they don't want to do the work :)
A gov't worker not wanting to do their job? NO WAY!
-
More progress on the 12 x 40ft lean-to for my trailer parking.
(https://i.imgur.com/064CQUM.jpg)
(https://i.imgur.com/pT2sk6r.jpg)
(https://i.imgur.com/Px67YaR.jpg)
Hand to tear out the soffit and facia boards bc I am laying the lean to rafters on the top plate of the shop wall and tie them into the roof trusses right at the top plate as well.
(https://i.imgur.com/SdAObxv.jpg)
(https://i.imgur.com/hgGfqh3.jpg)
-
chipper works great, basically just mulching the flower beds with the debris. Bagging the material would be an extra step. The exhaust/mulch just blows the bag away. I do need a bigger gas can, it does suck up the fuel. Now to get through the 25x25 debris pile and start a new one. that and 500 other projects
-
chipper works great, basically just mulching the flower beds with the debris. Bagging the material would be an extra step. The exhaust/mulch just blows the bag away. I do need a bigger gas can, it does suck up the fuel. Now to get through the 25x25 debris pile and start a new one. that and 500 other projects
Chop, Chop...that debris ain't gonna chip itself.
-
chipper works great, basically just mulching the flower beds with the debris. Bagging the material would be an extra step. The exhaust/mulch just blows the bag away. I do need a bigger gas can, it does suck up the fuel. Now to get through the 25x25 debris pile and start a new one. that and 500 other projects
Chop, Chop...that debris ain't gonna chip itself.
Would that be CHIP CHIP....
-
chipper works great, basically just mulching the flower beds with the debris. Bagging the material would be an extra step. The exhaust/mulch just blows the bag away. I do need a bigger gas can, it does suck up the fuel. Now to get through the 25x25 debris pile and start a new one. that and 500 other projects
Chop, Chop...that debris ain't gonna chip itself.
Would that be CHIP CHIP....
.(https://uploads.tapatalk-cdn.com/20201208/2fa9d11b5cfe0f400e57d73cba2bc121.jpg)
Sent from my SM-G960U using Tapatalk
-
lol
-
More progress in between rain.
(https://i.imgur.com/ReU3wGt.jpg)
(https://i.imgur.com/DFgjatL.jpg)
(https://i.imgur.com/xHMmJJb.jpg)
-
Needed to get more done on the lean-to so I stuck the kids in the outdoor pack-n-play with some wood blocks 😂
(https://i.imgur.com/i8vX9FH.jpg)
(https://i.imgur.com/DOoRJAu.jpg)
(https://i.imgur.com/KBC5knI.jpg)
(https://i.imgur.com/yaLNKCI.jpg)
-
Looks good Scott!!
-
Is there an engineering rationale behind having 6x6 posts but only using 2 2x width on them?
-
Nice work,Scott.
-
Is there an engineering rationale behind having 6x6 posts but only using 2 2x width on them?
You serious cork?
Sent from my iPhone using Tapatalk
-
Is there an engineering rationale behind having 6x6 posts but only using 2 2x width on them?
You serious cork?
Sent from my iPhone using Tapatalk
Uh, of course not...but let's suppose I was, why don't you explain it to me.
Sent from my SM-G960U using Tapatalk
-
You always want a good foundation. Then you can just stack anything on it.
-
Wrapped up a pretty big project today. Cabinets and granite were outsourced. I did the plumbing, flooring, trim, and electrical.
Before and after:
(https://uploads.tapatalk-cdn.com/20201223/beed1d8b4239275ee31c01a96962cfe2.jpg)
(https://uploads.tapatalk-cdn.com/20201223/536ec7d96b24ec1e59d331e2a561d57d.jpg)
Sent from my iPhone using Tapatalk
-
Wrapped up a pretty big project today. Cabinets and granite were outsourced. I did the plumbing, flooring, trim, and electrical.
Before and after:
(https://uploads.tapatalk-cdn.com/20201223/beed1d8b4239275ee31c01a96962cfe2.jpg)
(https://uploads.tapatalk-cdn.com/20201223/536ec7d96b24ec1e59d331e2a561d57d.jpg)
Sent from my iPhone using Tapatalk
A small but mighty whisky collection. Nicely done!
-
Very nice Tmac!!
-
Looks good.
-
Nice work!
Sent from my iPhone using Tapatalk Pro
-
Big transformation there @TravisMac
[beer]
-
Nice job tmac!
-
Nice Tmack, when's the house warming party?
Sent from my SM-G975U using Tapatalk
-
Nice Tmack, when's the house warming party?
Sent from my SM-G975U using Tapatalk
Cmon over!
-
Nice Tmack, when's the house warming party?
Sent from my SM-G975U using Tapatalk
Cmon over!
I don't think you'll be awake by the time I'd get there.
Sent from my SM-G975U using Tapatalk
-
Final build cost for lean-to #1 is in, $1,960!! Works out to $3.77/sq ft of usable dry storage area (520 sq ft).
That’s a lot of money for a basic structure!
-
Final build cost for lean-to #1 is in, $1,960!! Works out to $3.77/sq ft of usable dry storage area (520 sq ft).
That’s a lot of money for a basic structure!
The real question is how much less and how much faster could someone else have done it for?
-
Final build cost for lean-to #1 is in, $1,960!! Works out to $3.77/sq ft of usable dry storage area (520 sq ft).
That’s a lot of money for a basic structure!
The real question is how much less and how much faster could someone else have done it for?
wow
-
Final build cost for lean-to #1 is in, $1,960!! Works out to $3.77/sq ft of usable dry storage area (520 sq ft).
That’s a lot of money for a basic structure!
Quite a value. Nice work Scott!
-
Did I miss the final pics?!
-
Did I miss the final pics?!
I'm gonna guess yes
-
Did I miss the final pics?!
I'm gonna guess yes
I don’t see a completed pic
-
Did I miss the final pics?!
You didn’t miss them. I haven’t posted yet. Still have some metal roof panels to put on and I need to paint the posts. Since I have everything purchased i just had to know the final $$s
-
Final build cost for lean-to #1 is in, $1,960!! Works out to $3.77/sq ft of usable dry storage area (520 sq ft).
That’s a lot of money for a basic structure!
The real question is how much less and how much faster could someone else have done it for?
wow
Should have slapped an emoji or two on there! The sarcasm was very much lost on that one. Oops!
-
Final build cost for lean-to #1 is in, $1,960!! Works out to $3.77/sq ft of usable dry storage area (520 sq ft).
That’s a lot of money for a basic structure!
The real question is how much less and how much faster could someone else have done it for?
wow
Should have slapped an emoji or two on there! The sarcasm was very much lost on that one. Oops!
It seemed out of character for you.
Sent from my SM-G960U using Tapatalk
-
Ok so you I ran out of screws for the metal panels, so after buying more the total build cost comes in at $2,020.
Here are the completed pics. I will be repairing/painting the shop in the summer/fall time frame. When I do, I plan to add an overhang over the garage door and paint the trim black to have it all match.
(https://i.imgur.com/ed2WYMO.jpg)
(https://i.imgur.com/7IqlnfX.jpg)
(https://i.imgur.com/9CK2vvP.jpg)
-
^^^
That sure is a nice place to keep the trailer. Well done!
-
Holy cow. I bet painting those rafters was the worst part.
Sent from my iPhone using Tapatalk Pro
-
Ok so you I ran out of screws for the metal panels, so after buying more the total build cost comes in at $2,020.
Here are the completed pics. I will be repairing/painting the shop in the summer/fall time frame. When I do, I plan to add an overhang over the garage door and paint the trim black to have it all match.
So, it'll be done in fall/winter 2022...gotcha :)
I'd love to have that setup...nicely done.
Sent from my SM-G960U using Tapatalk
-
Looks awesome Scott
-
Holy cow. I bet painting those rafters was the worst part.
Sent from my iPhone using Tapatalk Pro
Yes it was. I actually only painted the fronts of the rafters...you know, curb appeal and all.
-
So, it'll be done in fall/winter 2022...gotcha :)
Accurate statement right there!
-
Those are blueberry bushes right at the edge along the posts...I was told that was my boundary and not to impact future blueberry picking.
-
Looks great, Scott.
-
All the lean-to work paid off. I was able to pull out a dry trailer, load up, move back under and strap down the Jeep all while staying dry....priceless.
(https://i.imgur.com/7MhMsCf.jpg)
(https://i.imgur.com/ubxS8cq.jpg)
-
^nice
-
Really jealous right now
Sent from my iPhone using Tapatalk
-
Nicely done Scott!
-
That’s bad ass man! Jealous for sure!
Sent from my iPhone using Tapatalk Pro
-
So damn nice!!
-
lean-to FTW!!
-
That's awesome! The tractor looks like it's waiting on some mods now that the buggy is in it's spot lmao
-
I got my living room, kitchen, laundry room, and hallway flooring done and had new cabinets and countertop installed. Converted my tractor to quick attach and made some grapple forks.
My to-do list is finally clear for me to do some work on the LJ.
-
Looks good Larry
-
Nice Larry! Did you have to add the third function valve on your tractor or was it already on there?
-
Nice Larry! Did you have to add the third function valve on your tractor or was it already on there?
I added a diverter valve to the front.
https://www.amazon.com/gp/product/B078WGQV4P/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
-
one day my todo list at the house will allow me to do something with the jeep
-
Finally got around to painting the garage floor. 2/3 done!
(https://uploads.tapatalk-cdn.com/20210407/dcb41544a7fcbd0e9616a1274421bc70.jpg)
(https://uploads.tapatalk-cdn.com/20210407/889d1693f5a6b600c04e9d3de887a8d2.jpg)
Sent from my iPhone using Tapatalk
-
Finally got around to painting the garage floor. 2/3 done!
(https://uploads.tapatalk-cdn.com/20210407/dcb41544a7fcbd0e9616a1274421bc70.jpg)
(https://uploads.tapatalk-cdn.com/20210407/889d1693f5a6b600c04e9d3de887a8d2.jpg)
Sent from my iPhone using Tapatalk
This is always fun.
Sent from my SM-G975U using Tapatalk
-
Finally got around to painting the garage floor. 2/3 done!
Sent from my iPhone using Tapatalk
Very nice! What product did you use? Did you do an etching (or acid clean) before laying down the stuff?
Sent from my SM-G960U using Tapatalk
-
Finally got around to painting the garage floor. 2/3 done!
Sent from my iPhone using Tapatalk
Very nice! What product did you use? Did you do an etching (or acid clean) before laying down the stuff?
Sent from my SM-G960U using Tapatalk
The rustoleum epoxy Kit. I did it at our previous house and the garage floor still looked brand new when we moved (and made it easy to clean leaking fluids, etc). The concrete had a lot of old paint stains, oil stains, etc so I did a degreaser first and used an HD broom from harbor freight with steel bristles to work the stains, then pressure washed it off. Then etched it and pressure washed again. Prep took about 2 days, but from the reviews I read the longevity is all in the prep.
-
Looks good man. I’ve been wanting to do this to my garage also. Everything I read said the prep is what makes it last too. Sounds like You got that covered.
Sent from my iPhone using Tapatalk Pro
-
Garage floor coatings just give it that much more clean and finished look! I would like to do this to ours as well.
-
Garage floor coatings just give it that much more clean and finished look! I would like to do this to ours as well.
After doing it a second time, couple of things I have learned:
- For the flakes, I took an old food container (think like cottage cheese, or an old tupperware container) and drilled about 10 3/8" holes in the lid and used it like a salt shaker for the chips. It kept them a little more "random" instead of tossing them
- I bought the "grit" this time so that it wouldn't be so slick when its wet, but it was basically overpriced fine sand. If I did it again I would make another "shaker" and just use some regular sand. This stuff was so fine it didn't go down very uniformly
-
Garage floor coatings just give it that much more clean and finished look! I would like to do this to ours as well.
After doing it a second time, couple of things I have learned:
- For the flakes, I took an old food container (think like cottage cheese, or an old tupperware container) and drilled about 10 3/8" holes in the lid and used it like a salt shaker for the chips. It kept them a little more "random" instead of tossing them
- I bought the "grit" this time so that it wouldn't be so slick when its wet, but it was basically overpriced fine sand. If I did it again I would make another "shaker" and just use some regular sand. This stuff was so fine it didn't go down very uniformly
Solid tips thanks!
Sent from my iPhone using Tapatalk Pro
-
Looks good Travis....that's what we used on our garage floor.
-
Bought some gold....uh I mean lumber from Home Depot tonight to get started on my second lean-to off the workshop.
(https://i.imgur.com/AJ9lxqC.jpg)
(https://i.imgur.com/VqPtgVY.jpg)
-
Bought some gold....uh I mean lumber from Home Depot tonight to get started on my second lean-to off the workshop.
(https://i.imgur.com/AJ9lxqC.jpg)
(https://i.imgur.com/VqPtgVY.jpg)
Well look at moneybags over here [king]
-
I finished the last of the flooring in the house yesterday. Now I get to do a couple of minor repairs to the condo before renting it out at the end of the month.
-
My helper posing for a pic.
Got the 10x28 section of the deck done yesterday. Now I will start on the 12x28 section.
-
Another lean-to up.
(https://i.imgur.com/E8LoveT.jpg)
-
Nice ^^^
-
Small update.
-
Small update.
That’s a lot of deck
No homo