Georgia Trail Riders Forum

MEMBERS DISCUSSION AREA => General Discussion => Topic started by: 94xjsport94 on August 05, 2013, 04:06:18 PM

Title: Tubing bender
Post by: 94xjsport94 on August 05, 2013, 04:06:18 PM
I want to make a t case skid plate for my XJ similar to this one: (http://img.tapatalk.com/d/13/08/06/qyputa9a.jpg)

For my Clayton crossmember. Thinking a piece of HREW would work or if anyone has a piece of DOM I could have or buy cheap. I'll measure around down there but looking for help on the bender part... Probably source some 1/4" plate for the skid part and I can weld it together.
Title: Re: Tubing bender
Post by: bear991 on August 06, 2013, 08:41:43 PM
Will I'm fabing up a trusses for my jeep now out of chrome moly. Don't know how much you'll need but your welcome to what is left and my tubing bender when I'm done. I'll cut the one for the front tomorrow and let you know what is left over. PM me the measurements and I'll see what I can do
Title: Re: Tubing bender
Post by: 94xjsport94 on August 06, 2013, 08:49:23 PM
PM on the way. Where do you live?
Title: Re: Tubing bender
Post by: bear991 on August 06, 2013, 08:53:18 PM
I'm in Clayton, close to the Ga. N.C. line.
Title: Re: Tubing bender
Post by: 94xjsport94 on August 06, 2013, 08:56:21 PM
Talked to my friend on NAXJA. He seems to think I'll need a whole 10' stick since the bends take up a lot. Probably go with 1 1/4 HREW and 1/4" plate and have him help me out. He lives in Decatur I think... He told me to buy the metal and he'll help me fab it up too.
Title: Re: Tubing bender
Post by: Oscar_Mike 2013 on August 07, 2013, 01:19:44 PM
Quote from: 94xjsport94 on August 06, 2013, 08:56:21 PM
Talked to my friend on NAXJA. He seems to think I'll need a whole 10' stick since the bends take up a lot. Probably go with 1 1/4 HREW and 1/4" plate and have him help me out. He lives in Decatur I think... He told me to buy the metal and he'll help me fab it up too.
Great. I'll need your friend to help me fab up a step for my wife on the passenger side. Any taller and she won't be able to get in.
Title: Re: Tubing bender
Post by: 94xjsport94 on August 07, 2013, 01:37:26 PM
Ok lol. He is a fabricator by trade, you should have seen his XJ, The Teal Bitch, before it was chopped.
Title: Re: Tubing bender
Post by: prjohnson on August 07, 2013, 03:57:13 PM
Quote from: Oscar_Mike 2013 on August 07, 2013, 01:19:44 PM
Quote from: 94xjsport94 on August 06, 2013, 08:56:21 PM
Talked to my friend on NAXJA. He seems to think I'll need a whole 10' stick since the bends take up a lot. Probably go with 1 1/4 HREW and 1/4" plate and have him help me out. He lives in Decatur I think... He told me to buy the metal and he'll help me fab it up too.
Great. I'll need your friend to help me fab up a step for my wife on the passenger side. Any taller and she won't be able to get in.

Saw someone use this, but attached it to the inside. It worked great & doesn't hang down.

(http://ep.yimg.com/ca/I/allthingsjeep_2267_105303361)

http://www.allthingsjeep.com/red32101.html